Micro Motion RFT9709 Bedienerhandbuch Seite 46
- Seite / 74
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
38
RFT9709 Transmitter Instruction Manual
Troubleshooting
continued
Table 4-4. Default values after a master reset
Characterization variables
Default Default
Flow calibration factor 1.00005.13 Pressure
Density Pressure polling No
Density A 0.0000 g/cc Field device tag DP CELL!
K1 density constant 5000.00 Pressure input at 4 mA 0.00 psi
Density B 1.0000 g/cc Pressure input at 20 mA 1000.00 psi
K2 density constant 50000.00 Pressure correction for flow 0.00% per psi
Density temperature coefficient 4.44% per 100°C Pressure correction for density 0.00 g/cc per psi
FD density constant 0.000 Flow calibration pressure 0.00 psi
Mass flow factor 1.0 RTD parameters
Volume flow factor 1.0 0°C = 100.0 Ω
Density factor 1.0 100° = 138.5 Ω
Viscosity calibration factor 1.000000.00000 API table Disabled
Measurement units
Default Default
Mass flow unit g/sec Temperature unit °C
Volume flow unit l/sec Viscosity unit centipoise
Density unit g/cc Pressure unit psi
Field device variables
Default Default
Mass flow cutoff 0.00 g/sec Low slug flow limit 0.0000 g/cc
Volume flow cutoff 0.0000 l/sec High slug flow limit 5.0000 g/cc
Flow direction Forward only Internal damping on density 2.00 sec
Internal damping on flow 0.80 sec Internal damping on temperature 4.00 sec
Transmitter output variables
Default Default
Primary mA output variable Mass flow Frequency/pulse output variable Mass flow
Upper range value 160.00 g/sec Frequency 10000.00 Hz
Lower range value –160.00 g/sec Rate 15000.00 g/sec
Added damping 0.00 sec Maximum pulse width 0.50 sec
Secondary mA output variable Temperature Control output Flow direction
Upper range value 450.00°C Slug duration 1.00 sec
Lower range value –240.00°C Polling address 0
Added damping 0.00 sec Burst mode Off
Burst command 2
Device information
Default Default
Transmitter tag name
M
.
RESET
Sensor model Unknown
Description
CONFIGURE
XMTR
Sensor flow tube material Unknown
Message
MASTER
RESET
-
ALL
DATA
DESTROYED
Sensor flange type Unknown
Sensor flow tube liner material None
Date 01/
JAN
/95
Communication settings
(standard communication)*
*Switch 5 set to the USER-DEFINED position. See Appendix C, page 47, for information on setting switches.
Default Default
Baud rate 9600 baud Protocol and physical layer Modbus RTU mode
(8 bits) on RS-485, and
HART (Bell 202) on PV
Stop bits and parity 1 stop bit, odd parity
09shoot.fm Page 38 Tuesday, March 2, 1999 9:26 AM
- Model RFT9709 1
- Transmitter 1
- Table of Contents 5
- Appendixes 6
- Before You Begin 10
- RFT9709 components 10
- Step 1 Mounting 11
- Mounting 12
- 1.2 Mounting options 12
- 1.3 Installation in user 12
- 1.4 Optional NEMA-housing 13
- Step 2 Wiring 15
- 2.2 Power supply wiring and 16
- 2.3 Sensor wiring 17
- Remotely-installed 19
- Cable connections to 20
- *Combined drain wires 21
- Figure 2-6. Wiring to ELITE 22
- CMF sensors 22
- Figure 2-7. Wiring to BASIS 23
- F, Model D, and DL sensors 23
- Primary and secondary 26
- Figure 2-10 26
- HART multidrop network 27
- Figure 2-11. Typical HART 27
- network wiring 27
- RS-485 output 28
- Figure 2-12. RS-485 wiring 28
- Frequency/pulse output 29
- Figure 2-13 29
- Control output 30
- Figure 2-14 30
- Control output terminals 30
- External zero switch wiring 31
- Figure 2-15 31
- Remote-zero switch wiring 31
- Viscosity measurement or 32
- Table 2-3 32
- Sensors affected by 32
- Step 3 Startup 35
- Startup 36
- Zeroing procedure 36
- Diagnosing zero failure 36
- 3.3 Event registers 37
- Table 3-1 37
- Parameters that affect 37
- 3.4 Totalizer reset 38
- 3.5 Process measurement 38
- Troubleshooting 39
- Switch Settings 40
- 4.3 Interrogation with the 41
- program 41
- Output test and trim 41
- Figure 4-2. ProLink 42
- PC-Interface connections 42
- Installation Step 2 43
- 4.6 Master reset 45
- 4.7 Customer service 45
- A RFT9709 Specifications 47
- RFT9709 Specifications 48
- Functional specifications 48
- API-2540 standard tables 49
- Input for pressure 49
- Hazardous area approvals 51
- B Ordering Information 53
- OUNDATION 54
- C Switch Settings 55
- C.3 Fault output settings 57
- C.4 Security modes 57
- Table C-2. Security modes 57
- Security mode 8 58
- Figure C-2 59
- Diagnostic LED and zero 59
- Appendix 61
- Figure D-1 61
- Configuring open collector 61
- E Decontamination and 63
- Return Goods Policy – USA 63
- IMPORTANT: 64
- F Decontamination and 65
- Return Goods Policy – Europe 65
- See also 69
- Micro Motion Inc. USA 74
- Worldwide Headquarters 74
- Micro Motion Europe 74
- Micro Motion Asia 74
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern